Anritsu MD8470A Скачать руководство пользователя страница 5

Страница: 5 / 114

For Safety

WARNING

3. When supplying power to this equipment, connect the accessory 3-

pin power cord to a grounded outlet. If a grounded outlet is not

available, before supplying power to the equipment, use a conversion

adapter and ground the green wire, or connect the frame ground on

the rear panel of the equipment to ground. If power is supplied

without grounding the equipment, there is a risk of receiving a severe

or fatal electric shock.

4. This equipment cannot be repaired by the operator. DO NOT attempt

to remove the equipment covers or unit covers or to disassemble inter-

nal components. Only qualified service personnel with a knowledge

of electrical fire and shock hazards should service this equipment.

There are high-voltage parts in this equipment presenting a risk of

severe injury or fatal electric shock to untrained personnel. In addition,

there is a risk of damage to precision components.

5. The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu service

personnel, or service personnel of an Anritsu sales representative,

should break this seal to repair or calibrate the equipment. If the

performance-guarantee seal is broken by you or a third party, the

performance of the equipment cannot be guaranteed.

6. This equipment should be used in the correct position. If the cabinet

is turned on its side, etc., it will be unstable and may be damaged if it

falls over as a result of receiving a slight mechanical shock.

And also DO NOT use this equipment in the position where the power

switch operation is difficult.

7. This instrument uses a Liquid Crystal Display (LCD); DO NOT subject

the instrument to excessive force or drop it. If the LCD is subjected

to strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested acci-

dentally, spit it out immediately, rinse your mouth with water and seek

medical help. If it enters your eyes accidentally, do not rub your

eyes, irrigate them with clean running water and seek medical help.

If the liquid gets on your skin or clothes, wash it off carefully and thor-

oughly.

Falling Over

LCD

Calibration

Repair

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 5 / 114

Результаты поиска

Содержание MD8470A

Отзывы: