Anritsu MD8470A Скачать руководство пользователя страница 62

Страница: 62 / 114

2.3.18 External monitor

The

VGA

connector located on the rear panel of the MD8470A is a 15-pin

Mini D-Sub connector for connecting to an external monitor. An external

display can be used if the external display designation is set to enabled.

Refer to Section 3.2.11 “Using external monitor” for details.

The rear panel of the MD8470A has

Call Proc Timing I/O

connectors, which

are identical 15-pin Mini D-Sub connectors. Check the connector labels

when connecting and be careful so as not to connect to the wrong connec-

tion point.

2.3.19 Allowable maximum power to input into the connector

Do not input power beyond the allowable maximum power into the input

connector of the MD8470A. In addition, do not input a signal into the

output-only connector. The internal circuits may be damaged if a signal

is input into the output-only connector.

Table 2.3.19-1 Allowable maximum power

Connector Name

Allowable Maxi-

mum Power

RF Main / RF Aux1 / RF Aux2

+34 dBm

10MHz Ref Input

+20 dBm

Trigger I/O Input

LVCMOS Level

Call Proc. Timing I/O

LVCMOS Level

CAUTION

The MD8470A has no circuit that protects the internal cir-

cuit from power above the allowable maximum power. Do

not input power beyond the allowable maximum power.

Doing so may damage the internal circuits, which may

cause a fire or accident to occur.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 62 / 114

Результаты поиска

Содержание MD8470A

Отзывы: