Anritsu MD8470A Скачать руководство пользователя страница 58

Страница: 58 / 114

2.3.11 ISDN connectors

The

ISDN0

connector on the rear panel of the MD8470A main unit is a

connector for connecting to an ISDN device (BRI). Use a cable with

shielding in order to observe radiation interference specifications.

The

ISDN1

connector on the rear panel of the MD8470A main unit is a

connector for connecting to an ISDN device (PRI). It is currently un-

available.

The

ISDN

connector can be used only when the MU847090A/B ISDN In-

terface Unit is installed. Refer to the Operation Manual of the simula-

tion kit for detailed test methods using ISDN devices.

The rear panel of the MD8470A has

Call Proc Ethernet

connectors and

Ethernet

connectors, which are identical RJ-45 connectors. Check the

connector labels when connecting and be careful so as not to connect to

the wrong connection point.

ISDN device

(TV Phone, etc.)

When connecting to ISDN0 connector

Name plate

Fig. 2.3.11-1 Example of connection to ISDN device

For the MU847090A ISDN Interface Unit, terminate the line on the net-

work side externally. If the line is not terminated at a connected ISDN

device, use the marketed termination box, etc.

Termination

box

MD8470A

ISDN device

OUT

In addition, the MU847090B ISDN Interface Unit terminates the line in-

ternally.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 58 / 114

Результаты поиска

Содержание MD8470A

Отзывы: