Anritsu MD8470A Скачать руководство пользователя страница 42

Страница: 42 / 114

2.2 Installation

Install the MD8470A after taking out it from the packing box and check-

ing its contents. This section describes how to install the MD8470A and

other caution notes.

2.2.1

Transport

Hold the grips attached on the right and left, and keep the device level

when transporting it.

CAUTION

Do not move when the power is ON. Internal circuits

may be damaged and cause a fire, electric shock or

accidents to occur.

Hold the grips attached on the right and left and keep

the device level when transporting it. Holding the

grip on only one side when transporting this equip-

ment places excessive force on internal precision

components and may result in damage.

2.2.2

Install location environment conditions

Install the MD8470A in a stable location with a temperature of +5 to

+40

C. Install rear and sides in a location with more than 10 cm sepa-

rating it from obstructions such as walls and peripheral devices so as not

to block the area around the exhaust air opening.

Min 10 cm away

Fig. 2.2.2-1 Installation location

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 42 / 114

Результаты поиска

Содержание MD8470A

Отзывы: