Ametek Sorensen XG Скачать руководство пользователя страница 273

Страница: 273 / 381

Communications Options

M370430-01 Rev B

6-63

SYSTem:COMMunicate:LAN:HOST

This command will set the Host name. The name is limited to 16 characters

Command Syntax

SYSTem:COMMunicate:LAN:HOST <SRD>

Parameters

<SRD>

Example

SYST

:COMM:LAN:HOST “ACS”

Query Syntax

SYST:COMM:LAN:HOST?

Returned Parameters

<SRD>

SYSTem:COMMunicate:LAN:PASSword

This command will set the user password. The password is used to access to LAN
configuration screen from the Web

page. The default password is “admin”. The

description is limited to 8 characters.

Command Syntax

SYSTem:COMMunicate:LAN:PASSword <SRD>

Parameters

<SRD>

Example

SYST:COMM:LAN:PASS “admin”

Query Syntax

SYST:COMM:LAN:PASS?

Returned Parameters

<SRD>

SYSTem:COMMunicate:LAN:PORT

This command will set the socket port number. The query format returns the port
number set. The default value is 5025.

Command Syntax

SYSTem:COMMunicate:LAN:PORT<NRF>

Parameters

0- 65535

Example

SYST:COMM:LAN:PORT 5025

Query Syntax

SYST:COMM:LAN: PORT?

Returned Parameters

<NR1>

SYSTem:COMMunicate:LAN:MACAddress

This command allows for reading out the MAC address. This command can only be
used to query the MAC address. The MAC address is set at the factory and may not
be changed.

Command Syntax

SYSTem:COMMunicate:LAN:MACAddress

Parameters

None

Example

SYST:COMM:LAN:MACA?

Query Syntax

SYST:COMM:LAN:MACA?

Returned Parameters

<SRD>

Содержание Sorensen XG






























































































































































































































































































































































































Результаты поиска

Содержание Sorensen XG

Отзывы:

Похожие инструкции для Sorensen XG

Бренды по названию

Популярные бренды

Ametek Sorensen XG, Руководство по эксплуатации

Результаты поиска

Содержание Sorensen XG

Отзывы:

Похожие инструкции для Sorensen XG

Бренды по названию

Популярные бренды