Ametek Sorensen XG Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 381

Ametek Sorensen XG Скачать руководство пользователя страница 8

Safety

vi

M370430-01 Rev B

Standard Warnings

WARNING: Keep these instructions

This chapter contains important safety and operating instructions. Read and
keep this Operating Manual for future reference.

1.

Before installing and using the XG and XTR Family Programmable
DC Power Supply, read all instructions and cautionary markings on
the instrument and all appropriate sections of this Manual.

2.

This instrument is for indoor use only. Do not expose the instrument
to moisture. To reduce risk of fire hazard, do not cover or obstruct
the ventilation openings. Be sure to install the instrument in a
compartment which allows air to reach the ventilation inlets on the
front and rear of the unit to prevent overheating. For more
information, see “Ventilation” on page 2-4.

3.

To avoid a risk of fire and electric shock, make sure that the existing
wiring is in good condition and the wire is not undersized. Do not
operate the instrument with damaged or substandard wiring.

4.

Do not operate the instrument if it has received a sharp blow, been
dropped, or otherwise damaged in any way. If the instrument is
damaged, see the Warranty on page ii.

5.

Do not disassemble the instrument. It contains no user-serviceable
parts. See the Warranty on page ii for instructions on obtaining
service. Attempting to service the instrument yourself may result in
a risk of electrical shock or fire. Internal capacitors remain charged
after all power is disconnected.

6.

To reduce the risk of electrical shock, disconnect AC power from
the instrument before attempting any maintenance or cleaning or
working on any circuits connected to the instrument. Turning off
controls will not reduce this risk.

«
...
6
7
8
9
10
...
»

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов