manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 271 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 271

 
 
 

Communications Options 

 

M370430-01  Rev B 

6-61 

6 

SYSTEM COMMANDS 

The system commands control the system-level functions of the 
power source. 

Subsystem Syntax

 

SYSTem 
      :COMMunicate 
          :LAN 
              :ADDRess 

 

Set LAN IP address 

              :APPLy 

 

Apply the change in setting 

              :CLASs 

 

Set LAN Host bits 

              :DEFault 

 

Set  LAN  to  a  default  known 

setting 

              :DESCription 

 

Set user description 

              :DNSaddress 

 

Set LAN DNS address 

              :GWADdress 

 

Set LAN Gateway 

              :PASSword 

 

Set LAN password 

              :PORT 

 

Set LAN socket port address 

              :MACAddress 

 

Read the MAC address 

 

SYSTem:COMMunicate:LAN:ADDRess 

This command will set the LAN IP address. The query format returns the IP address 
set. To query the actual IP address used by the LAN interface (in case the IP address 
is  not  static  but  assigned  by  a  DHCP  server),  the  NCON  parameter  (Network 
Connection Setting) must be added to the query. The default value is 0.0.0.0. 

Command Syntax 

SYSTem:COMMunicate:LAN:ADDRess <NRF> 

Parameters 

ddd.ddd.ddd.ddd <IP address> 

Example 

SYST:COMM:LAN:ADDR 255.255.167.2  

Query Syntax 

SYST:COMM:LAN:ADDR? 

 

SYST:COMM:LAN:ADDR? NCON 

Returned Parameters 

<CRD> 

 

SYSTem:COMMunicate:LAN:APPLy 

This  command  will  apply  the  changes  in  LAN  setting.  The  controller  will  go  to  reset 
condition and the new LAN setting will take effect. 

Command Syntax 

SYSTem:COMMunicate:LAN:APPLy 

Parameters 

none 

Example 

SYST:COMM:LAN:APPL  

Query Syntax 

no query for this command 

Returned Parameters 

none 

SYSTem:COMMunicate:LAN:CLASs 

This command will set the number of host address bits or a class. The query format 
returns the number of bits  set. To query  the  actual number of bits used by  the LAN 
interface  (in  case  the  IP  address  is  not  static  but  assigned  by  a  DHCP  server),  the 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов