Ametek Sorensen XG Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 381

Ametek Sorensen XG Скачать руководство пользователя страница 24

Introduction

1-2

M370430-01 Rev B

Features and Options

The XG /XTR Family Programmable DC Power Supply provides stable,
variable output voltage and current for a broad range of development and
system requirements. The power supplies have a high power density and
numerous industry standard interfaces:

RS-232, RS-485, analog programming (APG), and USB built-in
ports.

Optional GPIB or Ethernet (ENET), isolated analog programming
(ISOL), control for remote operation and readback.

Seamless switching between front panel and any digital interface
(RS-232, RS-485, USB, GPIB or ENET).

Simultaneous digital displays for both voltage and current.

Front panel control by rotary Adjust/Enter knob, permitting high
resolution output setting.

Active Power Factor Correction (PFC) reduces input current and
input current harmonics.

Automatic crossover system allowing the power supply to switch
between Constant Current, Constant Voltage and Constant Power
(available in version 2.21 and higher) operating modes.

Parallel or series connection among multiple units to produce
greater diversity or to use in higher power applications.

Short-circuit protection of DC outputs provideing greater operating
safety.

Built-in APG and ISOL (optional) interface to provide a
galvanically isolated analog voltage control of the output,
master/slave output tracking, and remote Enable/disable for safety
and precision.

Remote output voltage sensing to automatically compensate for
cable losses.

Software calibrated.

Three user setting memory locations.

M10 Option preprograms the voltage to reset to zero upon power on
and upon output enable.

«
...
22
23
24
25
26
...
»

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов