Ametek Sorensen XG Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 381

Ametek Sorensen XG Скачать руководство пользователя страница 159

Remote Operation

M370430-01 Rev B

5-25

5

Multichannel Address Setting

The power supply multichannel address can be set to any address
between 1 to 30. All units that are connected together via the RS-232 or
RS-485 connector must have a unique multichannel address.

To set the address:

1.

Select the appropriate communication port as described
“Selecting the Appropriate Communication Port” on page
5-24.

If more than one unit has the same multichannel address when
connected through the RS-485 connector, then collisions are
possible, resulting in garbled responses to queries.

2.

Press the rotary Adjust/Enter control.

is displayed on the output voltage display.

3.

Turn the rotary Adjust/Enter control to select the desired

multichannel address between 1 to 30.

4.

Press the rotary Adjust/Enter control to commit the new

address.

«
...
157
158
159
160
161
...
»

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов