manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 160 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 160

 
 
 

Remote Operation 

 

5-26 

M370430-01  Rev B 

Remote Interface Addressing

 

All commands must be issued with a multichannel address or the device 
must be selected using the:

 

*adr or :SYST[<channel>]:COMM[:MCH]:ADDR commands. 

Once a device is selected all commands sent without a multichannel 
address will be handled by the selected device. The use of multichannel 
addresses supersedes the selected device as the destination for a 
message. For more details on how multichannel addresses affect 
responses, see Table 5-8.

 

To change the selected device simply issue the 

*adr 

or 

:SYST 

[<channel>] :COMM[:MCH] : ADDR 

command with a different 

multichannel address. The previously selected device will be deselected 
and the new device will be selected. From that point on, all messages 
without a multichannel address will be destined for the newly selected 
device. It is possible to deselect all devices by using the aforementioned 
commands with the broadcast address, 0.

 

The SCPI Commands for these instructions are:

 

[:]SYSTem:COMMunicate[:MCHannel]:ADDRess   <address> 

or

 

*ADR <address> 

Where:

 

<address> is the multichannel address of the device to be selected. The 
address is an integer value from 1 to 30.

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов