manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 272 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 272

 
 
 

Communications Options 

 

6-62 

M370430-01  Rev B 

NCON  parameter  (Network  Connection  Setting)  must  be  added  to  the  query.  The 
default value is 8. In general Class A network is 24 bits, Class B is 16 bits and Class A 
is 8 bits. 

Command Syntax 

SYSTem:COMMunicate:LAN:CLASs <NRF> 

Parameters 

8 to 32 

Example 

SYST:COMM:LAN:CLAS 8 

Query Syntax 

SYST:COMM:LAN: CLAS? 

 

SYST:COMM:LAN: CLAS? NCON 

Returned Parameters 

<NR1> 

SYSTem:COMMunicate:LAN:DEFault 

This  command  will  apply  the  changes  in  LAN  setting  to  the  default  setting.  The 
controller will go to reset condition and the default LAN setting will take effect. Both IP 
address  and  Gate  way  address  are  set  to  zero.  The  Host  name  is  cleared.  The 
password is reset to “admin”The unit is set to DHCP or Auto IP. 

Command Syntax 

SYSTem:COMMunicate:LAN:DEFault 

Parameters 

none 

Example 

SYST:COMM:LAN:DEF  

Query Syntax 

no query for this command 

Returned Parameters 

none 

SYSTem:COMMunicate:LAN:DESCription 

This command will set the user description. The description is limited to 24 characters 

Command Syntax 

SYSTem:COMMunicate:LAN:DESCription <SRD> 

Parameters 

<SRD> 

Example 

SYST:COMM:LAN:DESC “EVAL UNIT”  

Query Syntax 

SYST:COMM:LAN:DESC? 

Returned Parameters 

<SRD> 

SYSTem:COMMunicate:LAN:GWADdress 

This  command  will  set  the  LAN  Gateway  address.  The  query  format  returns  the 
Gateway address set. To query the actual gateway address used by the LAN interface 
(in  case  the  IP  address  is  not  static  but  assigned  by  a  DHCP  server),  the  NCON 
parameter  (Network  Connection  Setting)  must  be  added  to  the  query.  The  default 
value is 0.0.0.0. 

Command Syntax 

SYSTem:COMMunicate:LAN:GWADddress <NRF> 

Parameters 

ddd.ddd.ddd.ddd <Gateway address> 

Example 

SYST:COMM:LAN:GWAD 255.255.255.0  

Query Syntax 

SYST:COMM:LAN:GWAD? 

 

SYST:COMM:LAN:GWAD? NCON 

Returned Parameters 

<CRD> 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов