manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 199 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 199

 
 
 

Remote Operation 

 

M370430-01  Rev B 

5-65 

5 

Another benefit to the readback command is it allows the auto sequence 
program to be captured and stored on the client side for reloading when 
the program is to persist beyond power cycles.

 

Command:

 

[:]PROGram[<channel>]:READback?  

For Example: 

:PROG:START

 

*CLS

 

:VOLT 5.4

 

:CURR 0.25

 

*IDN?

 

:PROG:STOP

 

:PROG:READ?

 

Response:

 

*CLS 
:VOLT 5.4 
:CURR 0.25 
*IDN? 
:PROG:STOP 

Reloading an Auto Sequence Program: 

The following procedure will demonstrate how to store a command 
beyond a power cycle of the unit.

 

 

 

Important:

  

This functionality is only available through USB, RS-232 and 

RS-485. It is not possible to reload an auto sequence program over the GPIB and 
ENET cards.

 

To reload Auto Sequence program from file:

 

1.

 

Set the data rate of the device to be 1200 bps.

 

2.

 

Close the connection to the hyperterminal program and 

configure the connection data rate to be 1200 bps.

 

3.

 

Execute the program recording command: 

:PROG:START

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов