manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 79 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 79

 
 
 

Local Operation 

 

M370430-01  Rev B 

3-31 

3 

Defining the UVP Set Point

 

To define the UVP set point:

 

1.

 

Turn the power supply On.

 

2.

 

Set the output to the desired voltage.

 

3.

 

Turn the 9-position mode control to the PRT position. 

 is displayed.

 

4.

 

Turn the rotary Adjust/Enter control until 

 is 

displayed.

 

5.

 

Press the rotary Adjust/Enter control to select the UVP for 

setting up.

 

6.

 

Set up the lower limit protection using the rotary Adjust/Enter 

control.

 

 

 

Important:

  

 

The UVP range is variable from 0 volts to OVP

SET

 -10%.

 

 

7.

 

Once the desired value has been set, press the rotary 

Adjust/Enter control to commit the setting.

 

See “Coarse and Fine Adjustment Modes” on page 3-3.

 

The SCPI command (s) for these instructions are:

 

[[:]SOURce[<channel>]]:VOLTage:PROTection:UNDer[:LEVel]

 

 

Over Current Protection (OCP) 

The OCP alarm is a firmware alarm that is only configurable using the 
SCPI interface. The OCP triggers if the output current exceeds the OCP 
set point. Because the OCP alarm is a firmware based alarm it has a 
latency before detection of the condition can occur. The user should be 
aware of this latency and take this into consideration when relying on 
OCP to protect a sensitive load. The maximum period for detecting an 
OCP condition is 300 ms.

 

OCP is fixed at 110% of rated current.

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов