manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 63 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 63

 
 
 

Local Operation 

 

M370430-01  Rev B 

3-15 

3 

The reverse operating mode change can also occur if the load resistance 
is increased to the point that the required load current drops below the 
I

SET

 

value. At that point the power supply would crossover to CV mode 

and the load current would be free to vary as the load resistance 
changed.

 

L

o

a

d

 c

u

rr

e

n

t (

V

) 

L

o

a

d

 c

u

rr

e

n

t (

A

) 

 

Iset 

 

 

Figure 3-3 

Operating Modes

 

To set the voltage set point (VSET)

:

 

1.

 

Turn the 9-position mode control to the VOLTS position or 
press the rotary Adjust/Enter control if the 9-position mode 
control is already at the VOLTS position.

 

The voltage set point is blinking in the output voltage display. The 
output current will be displayed in the output current display.

 

2.

 

Set the desired voltage value using the rotary Adjust/Enter 
control.

 

 

 

Important:

  

If you can't get the set point to the desired level, you may need to 

change the set points for OVP.

 

3.

 

Press the rotary Adjust/Enter control to transition to Fine 
Adjust mode.

 

The set point will blink faster to indicate fine adjust tracking mode.

 

4.

 

Set the desired voltage value using the rotary Adjust/Enter 
control.

 

CV mode 

Crossover point 

CV mode 

Vset 

Load current  
 
Load voltage 

 

Load resistance (

Ω

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов