manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 142 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 142

 
 
 

Remote Operation 

 

5-8 

M370430-01  Rev B 

RS-485 Communication Cable with Two RJ-45s

 

Use the top connector of the two 8-pin RJ-45 jacks, as shown in Figure 
5-1, to connect to the RS-485 remote interface. Communication cable 
with two RJ-45 shielded connectors (see 

Figure 5-3) 

connecting the 

master unit to the slave unit. The cable length should be 9.84 feet (3 m) 
or longer. The pinouts for the RJ-45 plug on the master unit are the same 
as described in 

Table 5-7.

 

Table 5-7 

RJ-45 Plug on Slave Unit 

Pin 

Name 

Description 

1, 2 

NC 

No connection

 

3 

RXD+ 

Receive data 

Twisted 
pair 

4 

RXD- 

Receive data 

5 

TXD+ 

Transmit data

 

Twisted 
pair 

6 

TXD- 

Transmit data

 

7 

GND 

Ground

 

8 

NC 

No connection

 

 

 

Master unit (J6) 

Slave unit (J4) 

 

Figure 5-6 

RS-485 Communication Cable from Master to Slave Unit

 

 

Completing the Setup

 

To complete the setup:

 

 

Configure the XG/XTR to use the 485 remote interface and setup 
the terminal that will be used on the connected PC.

 

See sections entitled “Selecting the Appropriate Communication 
Port” on page 5-24 and “Terminal Configuration” on page 5-21 for 
more details.

 

RXD+ 
RXD

– 

TXD+ 
TXD

– 

 

GND 

RXD+ 
RXD

– 

TXD+ 
TXD

– 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов