manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 197 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 197

 
 
 

Remote Operation 

 

M370430-01  Rev B 

5-63 

5 

Setting Dwell Time 

The dwell time is the amount of time that is delayed between each 
command during the execution of an Auto Sequence program. The 
dwell time can be from 0 to 180 seconds and can be changed 
during the program execution. The dwell time has a minimum step 
size of 1 second.

 

Command:

 

[:]PROGram[<channel>][:STEP]:DWELl {?|<dwell time> } 

Where:

 

<dwell time > is an integer value from 0 to 180.

 

For Example:

 

:PROG:DWEL 12 Results in 12 seconds of wait time after each 
command is executed.

 

Storing an Auto Sequence Program: 

Loading a program into memory is done by using the 

[: ] 

PROGram [<channel>] [: RECord] : STARt

 command. After the 

start command has been issued, the XG/XTR will record all 
subsequent commands into the auto sequence program buffer. The 
commands will be recorded into the buffer until the  

: PROGram [<channel>] [: RECord] : STOP

 command is 

issued.

 

Commands:

 

[:]PROGram[<channel>][:RECord]:STARt  

[:]PROGram[<channel>][:RECord]:STOP 

 

 

Important:

  

If the start recording command is executed then any previously 

stored Auto Sequence program is deleted.

 

 

For example: 

:PROG:STAR  
:VOLT 12  
:OUTP ON  
:PROG:DWEL 60  
:OUTP OFF  
:OUTP ON  
:OUTP OFF

 

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов