Ametek Sorensen XG Скачать руководство пользователя страница 209 | Manualshive

Страница: 209 / 381

background image

Remote Operation

M370430-01 Rev B

5-75

5

Power Saving Control (Sleep Mode, XTR/XG 1700 W Only)

The Sleep Mode, supported by the XG/XTR family of DC power
supplies, is an effective way to reduce overall power consumption when
the power supply is not in use for a specified period of time. If Sleep
Mode is enabled, the power supply will revert to a low power
consumption mode with the following characteristics:

Display will be blank

The internal cooling fans will run at the lowest possible speed for

whisper quiet operation.

Touching any button or one of the rotary knobs will immediately

wake up the power supply to normal mode of operation.

All settings will be preserved during sleep mode and the power

supply will return to the previously set state when it wakes up.

The following conditions must be met in order for Sleep Mode to
engage:

The output of the power supply and auxiliary outputs must be off

(standby)

The Sleep Mode must be enabled (on).

To enable Sleep Mode:

Set a time delay for the duration of inactivity to elapse before entering
Sleep Mode. This time (sleep hold-off delay) can be set from the
Protection menu, under the SLP entry. The sleep hold off delay can be
set from 1 to 24 hours.

To disable the Sleep Mode:

Set the sleep hold off delay value to zero (0). This is also the default
state for the Sleep Mode feature. Thus, unless set from the front panel or
remotely using a SCPI command, Sleep Mode is off. Once enabled (set
to a value from 1 to 24), it will be enabled. If the set time elapses without
any activity on the power supply, it will enter Sleep Mode.

Note that after issuing a *RST command, the power supply will revert to
factory default settings which means Sleep Mode will be turned off.

Command:

[:]SYSTem[<channel>]:PROTection:SLEep <sleep_time>

Query Format:

[:]SYSTem[<channel>]:PROTection:SLEep?

«
...
207
208
209
210
211
...
»

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sorensen XG

Бренд: National Instruments Страницы: 8

Бренд: Parkside Страницы: 78

Бренд: Makita Страницы: 80

Бренд: Ironton Страницы: 21

Бренд: TMG Страницы: 19

Бренд: Felder Страницы: 10

Бренд: Echo Страницы: 24

Gardtec 500 series

Бренд: GARDINER TECHNOLOGY Страницы: 40

LI-HOME2V IMPACT218

Бренд: Valex Страницы: 16

Бренд: Surtek Страницы: 16

Бренд: X-Tronic Страницы: 8

GREAT STUFF PRO 13

Бренд: Dow Страницы: 4

Бренд: Pyramid Страницы: 3

Бренд: National Instruments Страницы: 11

PALMER POWER STATION

Бренд: M2TECH Страницы: 11

COMFORT CRIMP SHURE STAKE ERG4811

Бренд: Thomas & Betts Страницы: 2

Бренд: ASTRO TOOL Corp. Страницы: 2

Бренд: Metabo Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды