manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 198 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 198

 
 
 

Remote Operation 

 

5-64 

M370430-01  Rev B 

:PROG:DWEL   0  
:PROG:STOP 

This program will send a 12 V square wave with 120 seconds 50% duty 
cycle. When the program is finished, the dwell time is restored to 0 
seconds.

 

Saving an Auto Sequence Program to File: 

The following procedure indicates how to save an Auto Sequence 
program to a text file on the attached PC.

 

To save an Auto Sequence Program to a file:

 

1.

 

Start the text capture by selecting 

Transfer>Capture Text ...

 

from the Hyper Terminal program.

 

2.

 

Set the location and name of the auto sequence to be captured.

 

3.

 

Click the Start button.

 

4.

 

Execute a program read back by sending:

 

:PROG[<channel>]:READ?

 

5.

 

Stop the text capture by selecting 

Transfer>Capture 

Text>Stop 

from the Hyper Terminal program.

 

6.

 

Using any text editor open the file which you captured the 

Auto Sequence program to.

 

7.

 

Remove the first line which should read 

“:PROG[<channel>]:READ?” and the first blank line. This 
makes the first line of the program the first line of the file.

 

8.

 

Save the file and exit the text editor.

 

The Auto Sequence program has now been stored and can be sent 
to any unit. See “Reloading an Auto Sequence Program:” on page 
5-65 for details.

 

Readback and Troubleshooting an Auto Sequence Program: 

Since the Auto Sequence programming function records the 
commands at program time without verifying the syntax, it can be 
difficult to spot an error in the sequence, for example, if a typo was 
made when entering a command during the record phase. A 
readback command has been provided to output the stored auto 
sequence program currently in memory.

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов