manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 226 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 226

 
 
 

Communications Options 

 

6-16 

M370430-01  Rev B 

 

9.

 

In the IP Configuration section, click the radio button next to 

“Use the following IP configuration.”  

 

 

Important:

 

If you are working within a network system, please contact the 

network administrator for the appropriate information to complete the IP 
Address, Subnet Mask and Default Gateway fields.

 

 

10.

 

Click OK at the bottom of the page to complete the task. 

11.

 

Repeat this procedure for every power supply. Every device 
must have a unique fixed IP address. 

Selecting ENET as the Communication Port 

Once the XG/XTR unit with the ENET option has the option card 
configured, you’ll need to configure the XG/XTR to use the ENET 
option card as the active communication port.  

To select ENET as the communication port: 

1.

 

Turn the 9-position Mode control to PGM. 



 is displayed in the output voltage display. 

2.

 

Turn the rotary Adjust/Enter control to select the LAn 
communication port. 

3.

 

Press the rotary Adjust/Enter control. 



 is displayed on the output voltage display. 

4.

 

Turn the rotary Adjust/Enter control to select the desired 
address between 1 to 30.  

5.

 

Press the rotary Adjust/Enter control to commit the new 
address. 

 

Terminal Configuration 

The terminal program allows for communication with the power supply. 
To use a terminal program, set it up using the parameters from the 
following sections. If you wish to use HyperTerminal, see “Setting Up a 
HyperTerminal Connection” on page 6-17 for instructions. 

Data Format 

Serial data format is 8 bit, one stop bit. No parity bit. Flow control: 
none. 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов