Ametek Sorensen XG Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 381

Ametek Sorensen XG Скачать руководство пользователя страница 145

Remote Operation

M370430-01 Rev B

5-11

5

9.

In the Locate Driver Files dialog box, in the field Optional

Search Locations, select Specify A Location and click Next.

10.

On the next screen, enter the file path “C:\FTDI” and click

OK.

11.

On the next screen, select “Driver Files Search Results” and

click Next.

12.

In Completing the Found New Hardware Wizard, see Figure

5-9, click Finish to complete the installation.

Figure 5-9

Completing the New Hardware Wizard

This completes the first part of the installation during which the USB to
serial converter is installed. The second part involves the installation of
a serial port, which should follow automatically once the converter
installation is complete. Installation of the serial port does not require
any user intervention.

Verifying Installation

Once the installation of the serial port has completed, verify that the
installation has been successful by looking under Device Manager of the
System Properties screen. The device should have installed as a USB
Serial Port (COMx) attached to USB High Speed Serial Converter.

«
...
143
144
145
146
147
...
»

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов