Ametek Sorensen XG Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 381

Ametek Sorensen XG Скачать руководство пользователя страница 66

Local Operation

3-18

M370430-01 Rev B

Enabling the Auxiliary Output

To enable on the auxiliary output:

Press the OUTPUT ENABLE Aux button on the front panel.

The OUTPUT ENABLE Aux button will illuminate.

Important:

The auxiliary output will not be enabled if the external

AUX_ON_OFF signal line is being used to disable the auxiliary outputs. See
“AUX Output and Isolated Analog Programming (ISOL) Connector” on page
4-20.

To disable the auxiliary output:

Press the OUTPUT ENABLE Aux button on the front panel again.

The OUTPUT ENABLE Aux button will not be illuminated.

If the auxiliary output is activated, +5 V on J3.9 (+AUX1) and +15
V on J3.11 (AUX2) will be present with respect to Pin J3.2 or Pin
J3.6 (COM ISOLATED). (See also “AUX Output and Isolated
Analog Programming (ISOL) Connector” on page 4-20 for more
details.)

The SCPI command (s) for these instructions are:

[:]OUTPut[<channel>]:AUXiliary[:STATe]

Output Auto Start Mode (Auto Restart)

The Auto Start mode establishes the state of the output of the power
supply after recovery from a complete power cycle (all front panel
LEDs are not illuminated).

If Auto Start mode is set to On, the power supply output will return to its
previous value when the power supply is powered up again.

If Auto Start mode is set to Off, the power supply output will remain off
after the power supply is powered up again.

To change the Auto Start mode:

1.

Press and hold the OUTPUT ENABLE Main button for 1
second.

or

is displayed.

2.

Switch the Auto Start mode.

The SCPI command (s) for these instructions are:

[:]OUTPut[<channel>][:POWer][:STATe]:PowerON[:STATe]

«
...
64
65
66
67
68
...
»

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов