manualshive.com logo in svg

Ametek Sorensen XG, Руководство по эксплуатации, Страница: 286 / 381

Поделиться
Скачать
Ametek Sorensen XG Скачать руководство пользователя страница 286

 
 
 

Calibration and Troubleshooting 

 

7-10 

M370430-01  Rev B 

Non-isolated Analog Programming Calibration

 

Prior to this, the main output must be calibrated first.

 

 

 

Important:

  

In calibration commands, when + or - keys are expected, any other 

key will exit from the calibration mode.

 

Non-isolated Voltage Monitoring Calibration 

 

 

Important:

  

For maximum accuracy at a specific APG level, follow the 

calibration procedure again but use the intended operating voltage level in steps 
3 and 8.

 

To calibrate the non-isolated voltage monitoring:

 

1.

 

Disconnect the load and connect the voltmeter to the output.

 

2.

 

Connect the voltmeter to the non-isolated voltage monitoring 

output lines (J1.13 - J1.7).

 

3.

 

Set the Voltage APG level to 4 V. Send the SCPI command:

 

SYST:COMM:APR:LEV     4 

4.

 

Set the input source as Local. Send the SCPI command:

 

SYST:REM:SOUR     LOC 

5.

 

Set the main output voltage to 100% by sending the 

command:

 

SOUR:VOLT        <ModelVolt> 

or use the rotary adjust/Enter control.

 

6.

 

Turn the main output On by pressing the OUTPUT ENABLE 

Main button on the front panel or send the command:

 

:OUTP  ON 

The OUTPUT ENABLE Main button will illuminate.

 

7.

 

Enter interactive calibration mode by sending the SCPI 

command:

 

CAL:MON 

8.

 

Press on the terminal keys - or + to reduce or increase 

monitoring value. Adjust the monitoring value displayed on 
the voltmeter that was set up in Step 1 to read as close as 
possible to 4.000 V.

 

9.

 

Press any key other than the + or - keys to exit from 

interactive calibration mode.

 

Non-isolated Current Monitoring Calibration 

 

 

Important:

  

For maximum accuracy at a specific APG level, follow the 

calibration procedure again but use the intended operating voltage level in steps 
3 and 9.

 

Содержание Sorensen XG






























































































































































































































































































































































































Отзывы:

Нет отзывов