Allen-Bradley 1407-CGCM-DLR Скачать руководство пользователя страница 243

Страница: 243 / 268

Rockwell Automation Publication 1407-UM002B-EN-P - February 2019

243

Detailed CGCM-DLR Unit Tag Descriptions

Appendix

•

PhA_kVAR -

This tag reports the kVAR being produced by Generator

Phase A.

•

PhB_kVAR -

This tag reports the kVAR being produced by Generator

Phase B.

•

PhC_kVAR -

This tag reports the kVAR being produced by Generator

Phase C.

•

Avg_I -

This tag reports the Average Current of the active phases of the

generator.

•

PhA_I-

This tag reports the current in Generator Phase A.

•

PhB_I-

This tag reports the current in Generator Phase B.

•

PhC_I-

This tag reports the current in Generator Phase C.

•

AvgLLGenV -

This tag reports the Average Line-to-Line Voltage of the

active phases of the generator.

•

PhAB_GenV -

This tag reports the Line-to-Line Voltage between

Generator Phases A and B.

•

PhBC_GenV -

This tag reports the Line-to-Line Voltage between

Generator Phases B and C.

•

PhCA_GenV -

This tag reports the Line-to-Line Voltage between

Generator Phases C and A.

•

AvgLN_GenV -

This tag reports the Average Line-to-Neutral Voltage of

the active phases of the generator

•

PhA_GenV -

This tag reports the Voltage from Generator Phase A to

Neutral.

•

PhB_GenV -

This tag reports the Voltage from Generator Phase B to

Neutral.

•

PhC_GenV -

This tag reports the Voltage from Generator Phase C to

Neutral.

•

AvgLL_BusV -

This tag reports the Average Line-to-Line Voltage of the

active phases of the bus.

•

PhAB_BusV -

This tag reports the Line-to-Line Voltage between Bus

Phases A and B.

•

PhBC_BusV -

This tag reports the Line-to-Line Voltage between Bus

Phases B and C.

•

PhCA_BusV -

This tag reports the Line-to-Line Voltage between Bus

Phases C and A.

•

AvgLN_BusV -

This tag reports the Average Line-to-Neutral Voltage of

the active phases of the bus.

•

PhA_BusV -

This tag reports the Voltage from Bus Phase A to Neutral.

•

PhB_BusV -

This tag reports the Voltage from Bus Phase B to Neutral.

•

PhC_BusV -

This tag reports the Voltage from Bus Phase C to Neutral.

•

BusB_V –

Reference Bus voltage for the B reference in a dual breaker

scenario.

•

Exc_V-

This tag reports the Excitation Voltage.

•

Exc_I –

This tag reports the Excitation Current.

Содержание 1407-CGCM-DLR













































































































































































































































































Результаты поиска

Содержание 1407-CGCM-DLR

Отзывы:

Allen-Bradley 1407-CGCM-DLR, Руководство пользователя, Страница: 243 / 268

Результаты поиска

Содержание 1407-CGCM-DLR

Отзывы: