manualshive.com logo in svg

Advance acoustic HydroCat 459020, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic HydroCat 459020 Скачать руководство пользователя страница 95

           

 Hydro Cat 5015B

  Service Manual

HYDRO-MAX SYSTEM

6

Reinstall the screen panel.

7

Drain and rinse the solution tank (see the 

SOLUTION SYSTEM 

chapter).

8

Remove the chemical metering barb and rinse it in hot, soapy water.  Use a pin to clean hardened
chemical from the hole in the barb.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

RECOVERY TANK REMOVAL

1

Drain and clean the recovery tank.

2

See Figure 2.  Remove the (2) drain hoses (one on each side of the tank).

3

Disconnect the squeegee hose from the bottom of the recovery tank.

4

Disconnect the vacuum hose from the right side of the recovery tank.

5

Disconnect the solution pump hose from the right side of the recovery tank.

6

Disconnect the wiring connector from the right side of the recovery tank.

7

Lift the recovery tank up and out of the machine.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SOLUTION PUMP REMOVAL

1

Open the right side access door.  The solution pump is located just below the battery.

2

Disconnect the wires to the solution pump.

3

Disconnect the hoses that are connected to the solution pump.

4

Remove the (4) bolts that hold the solution pump in place and lift the pump out of the machine.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SOLUTION PUMP HEAD REMOVAL

1

Open the right side access door.  The solution pump is located just below the battery.

2

Disconnect the wires to the pressure switch on the end of the pump head.

3

Remove the (3) screws that hold the pump head on the motor and slide it off the motor shaft.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

RECOVERY AND SOLUTION TANK CLEANING  (continued...)

92

Содержание HydroCat 459020




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды