manualshive.com logo in svg

Advance acoustic HydroCat 459020, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic HydroCat 459020 Скачать руководство пользователя страница 78

   

                Hydro Cat 5015B 

 Service Manual

SWEEP SYSTEM

3

After 1 minute, raise the broom, release the parking brake and move the machine out of the way, so that
the polished strip is visible.

4

See Figure 2.  If the strip is tapered, loosen the (2) “B” bolts.

FIGURE 2 HERE

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BROOM LEVEL ADJUSTMENT  (continued...)

B

D

C

Front

FIGURE 2

5

Use the (2) “C” adjustment bolts to lower the right end of the broom, if the right end of the strip is too
narrow, or to raise the broom if the right end of the strip is too wide.  The heads of the bolts should be
tight against the broom idler arm when the adjustment is completed.

6

Tighten the locknuts on the “C” bolts and tighten the “B” bolts.  Repeat steps 1-3 to check adjustment, re-
adjust if necessary.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BROOM REMOVAL / ROTATION

The sweeping broom should be replaced when the bristles are worn to a length of 1-3/4 inches (4.5 cm) or
less.

To remove the broom . . .

1

Open the lower access door on the right side of the machine and the inner broom housing door.

2

See Figure 2.  Loosen the locknut and turn bolt “C” clockwise to move the head of the bolt away from the
idler arm.

3

Remove the (2) “B” bolts and the self locking nut “D”.  Pull the idler arm assembly away from the broom
and slide the broom out of the broom housing.

75

Содержание HydroCat 459020




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды