manualshive.com logo in svg

Advance acoustic HydroCat 459020, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic HydroCat 459020 Скачать руководство пользователя страница 62

   

                   Hydro Cat 5015B

  Service Manual

WHEEL DRIVE SYSTEM

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

FORWARD & REVERSE SWITCH

 CAUTION!

SAFE OPERATION OF THE MACHINE MAY BE AFFECTED BY THE FORWARD AND REVERSE DRIVE
SWITCHES.  USE EXTREME CARE WHEN ADJUSTING OR REPLACING THE SWITCHES AND THEIR
OPERATING LINKAGE.

Before replacing or adjusting the forward or reverse switch...

1

Gently move the front of the drive pedal up and down in neutral, to check the free travel in the pedal.  If
there is more than 1/8 inch (3 mm) free travel at the front of the drive pedal, adjust bracket “G” (see
Figure 5) up or down to eliminate the free travel.

FIGURE 5

Forward Switch

Reverse Switch

K

J

Squeegee Lift Switch

H

G

2

Gently move the drive pedal to the full forward and full reverse position to check for binding or rough
operation.  Clean and lubricate the pedal and potentiometer linkage or replace defective parts as re-
quired.

3

Make sure that collar “H” is centered between the levers on the forward and the reverse switches.  If it is
not, loosen the (2) set screws in the collar, center the collar between the switch levers and tighten the set
screws.

4

Make sure that the (2) set screws in collar “H” face directly toward the front of the machine.  The speed
potentiometer linkage can bind if the collar is turned to the right or left.  If necessary, loosen the set
screws in the collar, turn it to the proper position and tighten the set screws.

59

Содержание HydroCat 459020




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды