manualshive.com logo in svg

Advance acoustic HydroCat 459020, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic HydroCat 459020 Скачать руководство пользователя страница 22

 

  

                  Hydro Cat 5015B 

 Service Manual

SOLUTION SYSTEM

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

TROUBLESHOOTING

Follow the instructions under the “Problem” that best describes the condition of the machine being serviced.

Also see the 

Hydro-Max II

 chapter for additional solution system troubleshooting information.

Before Troubleshooting, make sure that there is at least 6 inches of water in the solution tank and the solution
lever is pushed all the way forward, to the maximum ON position.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Problem:  Solution Leaks With Control Lever in OFF Position

1

Replace solution valve.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Problem:  Little or No Solution to Scrub Brushes

1

Check the adjustment of the (2) flow control valves.

2

Check filter screen at bottom of solution tank.

3

Check linkage between solution lever and main solution valve.

4

Check main solution valve to see if the ball inside the valve moves along with the lever on the side of the
valve.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Problem:  Uneven Solution Flow

1

Check the adjustment of the (2) flow control valves.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Problem:  Solution Lever Stuck in OFF Position

1

Lower scrub brushes - solution lever cannot be pushed forward with the brushes in the UP position.

19

Содержание HydroCat 459020




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды