manualshive.com logo in svg

Advance acoustic HydroCat 459020, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic HydroCat 459020 Скачать руководство пользователя страница 66

   

                   Hydro Cat 5015B

  Service Manual

WHEEL DRIVE SYSTEM

8

Watch the ohmmeter while pressing down on the front of the drive pedal.  The pedal should hit the
forward stop bolt (under the front of the drive pedal) when the meter reads 4500 ohms.

*

If the meter reads 4500 ohms before the pedal hits the stop bolt, release the pedal and adjust the bolt
upward.

*

If meter reads less than 4500 ohms when the pedal hits the stop bolt, adjust the stop bolt downward.

9

Connect the wires to the potentiometer, close the front panel and test the machine for proper operation.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SPEED POTENTIOMETER ADJUSTMENT  (continued...)

63

Содержание HydroCat 459020




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды