manualshive.com logo in svg

Advance acoustic HydroCat 459020, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic HydroCat 459020 Скачать руководство пользователя страница 12

SPECIFICATIONS AND MAINTENANCE

   Hydro Cat 5015B 

 Service Manual

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SQUEEGEE LIFT ACTUATOR LUBRICATION

•

Lower the squeegee and remove the recovery tank.

•

Apply a light coating of grease to the actuator shaft.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

DIFFERENTIAL OIL

Remove the dipstick under the operator’s seat to check the differential oil level.  Add 90W gear lube if neces-
sary, to bring the oil level up to the indentation on the dipstick.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BRUSH DRIVE GEAR CASE OIL

Remove the vented plug from the top of the gear case to check the oil level.  Add 140W gear lube if the oil
level is more than 1-1/2 inch (3.8 cm) below the top of the gear case.

9

Содержание HydroCat 459020




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды