Chapter 16 Route
UAG CLI Reference Guide
116
[no] dscp class {default |
dscp_class
}
Sets a DSCP class. Use
default
to apply this policy route to incoming
packets that are marked with DSCP value 0. Use one of the pre-
defined AF classes (including af11~af13, af21~af23, af31~af33, and
af41~af43) to apply this policy route to incoming packets that are
marked with the DSCP AF class.
The “af” entries stand for Assured Forwarding. The number following
the “af” identifies one of four classes and one of three drop
preferences. See
Assured Forwarding (AF) PHB for DiffServ on page
dscp-marking <0..63>
Sets a DSCP value to have the UAG apply that DSCP value to the
route’s outgoing packets.
dscp-marking class {default |
dscp_class
}
Sets how the UAG handles the DSCP value of the outgoing packets that
match this route. Set this to
default
to have the UAG set the DSCP
value of the packets to 0. Set this to an “af” class (including
af11~af13, af21~af23, af31~af33, and af41~af43) which stands for
Assured Forwarding. The number following the “af” identifies one of
four classes and one of three drop preferences. See
Forwarding (AF) PHB for DiffServ on page 117
for more details.
no dscp-marking
Use this command to have the UAG not modify the DSCP value of the
route’s outgoing packets.
exit
Leaves the sub-command mode.
[no] interface
interface_name
Sets the interface on which the incoming packets are received. The
no
command resets the incoming interface to the default (
any
).
any
means all interfaces.
[no] next-hop {auto|gateway
address
object
|interface
interface_name
|trunk
trunk_name
|tunnel
tunnel_name
}
Sets the next-hop to which the matched packets are routed. The
no
command resets next-hop settings to the default (
auto
).
[no] schedule
schedule_object
Sets the schedule. The
no
command removes the schedule setting to
the default (
none
).
none
means any time.
[no] service {
service_name
|any}
Sets the IP protocol. The
no
command resets service settings to the
default (
any
).
any
means all services.
[no] snat {outgoing-interface|pool
{
address_object
}}
Sets the source IP address of the matched packets that use SNAT. The
no
command removes source NAT settings from the rule.
[no] source {
address_object
|any}
Sets the source IP address that the matched packets must have. The
no
command resets the source IP address to the default (
any
).
any
means all IP addresses.
[no] sslvpn
tunnel_name
Sets the incoming interface to an SSL VPN tunnel. The
no
command
removes the SSL VPN tunnel through which the incoming packets are
received.
[no] trigger <1..8> incoming
service_name
trigger
service_name
Sets a port triggering rule. The
no
command removes port trigger
settings from the rule.
trigger append incoming
service_name
trigger
service_name
Adds a new port triggering rule to the end of the list.
trigger delete <1..8>
Removes a port triggering rule.
trigger insert <1..8> incoming
service_name
trigger
service_name
Adds a new port triggering rule before the specified number.
trigger move <1..8> to <1..8>
Moves a port triggering rule to the number that you specified.
[no] tunnel
tunnel_name
Sets the incoming interface to an IPSec VPN tunnel. The
no
command
removes the IPSec VPN tunnel through which the incoming packets are
received.
Table 60
Command Summary: Policy Route (continued)
COMMAND
DESCRIPTION
Summary of Contents for UAG Series
