Chapter 19 EPON Profile Configuration
NetAtlas EPON Manager User’s Guide
276
Operator
Select the operator that applies to the incoming packets.
Select == (equal to) and the matched packet must contain the field
exactly the same as what you specified in the Field and Value fields.
Select != (not equal to) and the matched packets must not contain the
field exactly the same as what you specified in the Field and Value fields.
Select <= and the matched packet must contain the field which is less
than or equal to what you specified in the Value field.
Select >= and the matched packet must contain the field which is greater
than or equal to what you specified in the Value field.
Select exists and the matched packet must include the field you specified
in the Field field.
Select !exists and the matched packet must not include the field you
specified in the Field field.
Select Always match and the packet always matches the profile
regardless of what you specified in the Field and Value fields.
Value
If you select L2 Destination MAC Address or L2 Source MAC Address
in the Field field, enter a destination or source MAC address.
If you select Link Index in the Field field, enter the index number of the
logical link on the ONU.
If you select L2 Length/Type in the Field field, enter the Ethernet type
number in hexadecimal value (0x0000 ~ 0xff0f).
If you select VLAN ID in the Field field, enter a VLAN ID number.
If you select IPv4 Protocol Type in the Field field, enter an IPv4
protocol number from 1 to 255.
If you select IPv4/IPv6 Protocol Type in the Field field, enter the IPv4
Protocol field or an 8-bit Next Header field in the IPv6 packet.
If you select IPv4 Dest. Address/IPv6 Dest. Address [63:0] in the
Field field, enter a 64-bit IPv4 destination IP address or the first 64 bits
of an IPv6 128-bit destination IP address.
If you select IPv6 Dest. Address [127:64] in the Field field, enter the
last 64 bits of an IPv6 128-bit destination IP address.
If you select IPv4 Source Address/IPv6 Source Address [63:0] in
the Field field, enter a 64-bit IPv4 source IP address or the first 64 bits of
an IPv6 128-bit source IP address.
If you select IPv6 Source Address [127:64] in the Field field, enter
the last 64 bits of an IPv6 128-bit source IP address.
Action
Index
This is the index number of the rule.
Active
Select this check box to enable this rule.
Clear this check box to disable the rule.
Table 138
EPON Profile Configuration > Add ONU Policy Rule Profile (continued)
LABEL
DESCRIPTION
Summary of Contents for NetAtlas
