Xerox WorkCentre 5687 Series, Service Manual, Page: 965 / 2320

August 2007
2-773
WorkCentre 5687 Family
OF4b
Status Indicator RAPs
Open output device door 11-519 Sheet near top exit sensor at
shutdown Perform 11-130-110,
11-132-110 RAP for
LCSS, 11-130-130,
11-132-130 RAP for
HCSS, 11-130-170,
11-132-170 RAP for
HCSS BM
Open output device door 11-521 Sheet near 2nd to top exit sen-
sor Perform 11-140-110,
11-142-110 RAP for
LCSS, 11-140-130,
11-142-130, 11-150-
130, 11-152-130 RAP
for HCSS, 11-140-
171, 11-142-171 RAP
for HVF, 11-140-170,
11-142-170 RAP for
HCSS BM
Open front door 08-555 Registration sensor detects
paper in registration area on
power-on or in standby. 08-150 Jam clearance. Per-
form 08-150, 08-151
RAP
Open front door 08-556 Paper in duplex path at power-
on or in standby Jam clearance. Per-
form 08-160, 08-161
RAP
Open left hand door 08-557 Paper over the registration sen-
sor when feeding from the
bypass tray Jam clearance. Per-
form 08-155, 08-156
RAP
Open front door 08-566 Sheet near duplex sensor Jam clearance
Open left hand door 08-567 Paper over the registration sen-
sor when feeding from the
bypass tray Jam clearance
Open front door 10-507 Sheet is near the IOT exit sen-
sor in the non-invert path Jam clearance
Open front door 10-508 Sheet is near the IOT exit sen-
sor in the left hand side of the
invert path Jam clearance
Open front door 10-509 Sheet is near the IOT exit sen-
sor in the right hand side of the
invert path Jam clearance
Open front door 10-511 Sheet near post fuser sensor Jam clearance
Open front door 10-512 IOT exit sensor paper in IOT
exit area at power -on or start
print Jam clearance. Per-
form 10-107, 10-108,
10-109, 10-110 RAP
Open front door 10-513 Sheet near IOT exit sensor Jam clearance. Per-
form 10-107, 10-108,
10-109, 10-110 RAP
Table 3 Status messages O to R
UI Message
Status
Code
Reason for Message Reference / Action
Open left hand door 08-550 Sheet over wait sensor Jam clearance. Per-
form 08-100 RAP
Open left hand door 08-551 Tray 1 feed sensor detects
paper in feed area on power-on
or in standby, 08-101 Jam clearance. Per-
form 08-101 RAP
Open left hand door 08-552 Tray 2 feed sensor detects
paper in feed area on power-on
or in standby. 08-102 Jam clearance. Per-
form 08-102 RAP
Open left hand door 08-554 Tray 4 feed sensor detects
paper in feed area on power-on
or in standby. 08-104 Jam clearance. Per-
form 08-104, 08-114
RAP
Open left hand door 08-565 Sheet near registration sensor Jam clearance
Open output device door 11-522 Sheet over the BM eject sensor Perform 11-180-170,
11-182-170 RAP
Open output device door 11-523 Sheet near the BM eject sensor Perform 11-180-170,
11-182-170 RAP
Open tray 1 08-561 Sheet near Tray 1 feed sensor.
08-106 Jam clearance. Per-
form 08-106 RAP
Open tray 2 08-562 Sheet near Tray 2 feed sensor Jam clearance
Open tray 3 08-553 Tray 3 feed sensor detects
paper in feed area on power-on
or in standby. 08-103 Jam clearance. Per-
form 08-103, 08-113
RAP
Open tray 3 08-563 Sheet near Tray 3 feed sensor Jam clearance
Open tray 4 08-564 Sheet near Tray 4 feed sensor Jam clearance
Option service removed 22-554 Unable to remove optional ser-
vice Refer to 22-410 to 22-
416, 22-777 RAP, 22-
417 RAP
Optional service installed 22-553 Service option installed
Optional service mismatch
detected 22-552 Service option mismatch
detected
Output Bin full 03-511 When the 90% full sensor is
cleared before the bin switch
timer expires. Printing will continue
automatically 15 sec-
onds after raised if the
Pause button is not
pressed.
Or when the Resume
button pressed.
Or Automatically 15
minutes after Pause
button pressed if
Resume button is not
pressed.
Output device communica-
tions fault. Please call for
assistance. 03-545 IOT-Finisher: three times retry
fail at 100 ms cycle communi-
cation - no response. 03-360 Perform 03-360, 03-
408 to 03-410, 03-418
RAP
Table 3 Status messages O to R
UI Message
Status
Code
Reason for Message Reference / Action