Xerox WorkCentre 5687 Series, Service Manual, Page: 2194 / 2320

August 2007
6-302
WorkCentre 5687 Family
dC131i, dC132
General Procedures & Information
dC132 NVM Initialization
There are 4 items under this heading:
• Copier NVM Initialization
• Network Controller NVM initialization
• Embedded Fax NVM initialization
• NVM to Install Condition
NOTE: Certain NVM settings are password protected.
Copier NVM Initialization
Purpose
The NVM initialization routine provides the means for the CSE to reset specific machine vari-
able NVM or all machine variable NVM non-volatile memory (with the exception of Protected
NVM for which a password is required) to their default values.
Description
If the machine configuration changes through the addition of an input or output device, an ini-
tialization of the NVM for that device must be performed to make sure that all configuration val-
ues are correct for that device.
NOTE: initialization does not affect the billing counter, accounting, fault counter, diagnostic
data, or auditron services. These, with the exception of billing counters, can be reset if the
machine is restored to the install state using the NVM to Install Condition procedure.
NOTE: The auditron (billing counters) is initialized using the auditron setup routine, refer to the
User Guide.
The market region configuration attribute must have been preset at the factory or at first install
to ensure that the NVM default values are regionally correct. Some post install configuration
can be performed using the configuration tool, refer to dC131 NVM Read / Write.
Procedure
1. Save the NVM to disk, GP 5.
2. Enter diagnostics, GP 1.
3. Select Diagnostic Routines.
4. Select Copier Routines, 132 NVM initialization-Copier.
5. Touch the appropriate button to select the NVM to be initialized and follow the on screen
instructions. Refer to Table 1, for the functions that are reset to default.
• All Copier NVM.
• Machine Variable NVM, (i.e. paper path, platen and DADH registration).
• SA / KO Dust Off.
• System Counters Dust Off
NOTE: The NVM window will gray out while the initialization is in progress.
6. Switch off the machine, then switch on the machine, GP 14.
Network Controller NVM initialization
Purpose
To return to default network settings, configuration and flags.
20-909 FaxIntDtnNum-
CellPatt Int Dtone number cell pat-
tern Range = 0 to 3 2
20-911 FaxIntDtoneMak
eMin1 Int Dtone make min 1 Range = 0 to 10000 ms 130
20-912 FaxIntDtoneMak
eMax1 Int Dtone make max 1 Range = 0 to 10000 ms 270
20-913 FaxIntDtoneMak
Hole1 Int Dtone make hole 1 Range = 0 to 10000 ms 0
20-914 FaxIntDtoneBrek
Min1 Int Dtone 1 break min 1 Range = 0 to 10000 ms 130
20-915 FaxIntDtoneBrek
Max1 Int Dtone break max 1 Range = 0 to 10000 ms 270
20-917 FaxIntDtoneIdxN
xtC1 Int Dtone idx next cell 1 Index of next pattern
Range = 0 to 255 1
20-919 FaxIntDtFlgDtPe
rfd1 Int Dtone flag detection per-
formed 1 Range = 0 to 1 0
20-920 FaxIntDtoneMak
eMin2 Int Dtone make min 2 Range = 0 to 10000 ms 490
20-921 FaxIntDtoneMak
eMax2 Int Dtone make max 2 Range = 0 to 10000 ms 710
20-922 FaxIntDtoneMak
eHole2 Int Dtone make hole 2 Range = 0 to 10000 ms 40
20-923 FaxIntDtoneBrk
Min2 Int Dtone break min 2 Range = 0 to 10000 ms 850
20-924 FaxIntDtoneBrk
Max2 Int Dtone break max 2 Range = 0 to 10000 ms 1150
20-928 FaxIntDtFlgDetP
rfd2 Int Dtone flag detection per-
formed 2 Is this the last detection
pattern?
Range 0 to 1 1
Table 6 Jordan NVM values
Location NVM Name NVM Description Value Default