Xerox WorkCentre 5687 Series, Service Manual, Page: 188 / 2320

August 2007
1-8
WorkCentre 5687 Family
SCP 5
Service Call Procedures
SCP 5 Subsystem Maintenance
Use the Subsystem Maintenance to maintain the machine.
Procedure
WARNING
Switch off the electricity to the machine, GP 14. Disconnect the power lead from the
customer supply while performing tasks that do not need the electricity. Electricity can
cause the death or injury. Moving components can cause the injury.
Go to the correct procedure:
• Installation of New Parts
• HFSI
• Lubrication
• How to Clean the Machine
Installation of New Parts
The design life of the major components are shown in Table 1.
NOTE: If a range of machine speeds are specified within Table 1, the life expectancy for the
part will be specific for that machine.
If the speed has not been specified, the life expectancy for the part applies to all machines
within the product family.
HFSI
The High Frequency Service Items are shown in Table 2. To change HFSI settings, refer to GP
17 High Frequency Service Items.
Table 1 Component design life
Part Life Parts list reference
Fuser module
32-55 ppm
65-87 ppm
400k prints
400k prints PL 10.8 Item 1
PL 10.10 Item 1
Ozone filter
32-55 ppm
65-87 ppm
350k prints
400k prints PL 9.25 Item 3
PL 9.25 Item 3
Xerographic module
32-38 ppm
45-87 ppm
200k prints
400k prints PL 9.22 Item 2
PL 9.20 Item 2
Toner cartridge
32-55 ppm
65-87 ppm
30k prints at 6% area coverage
45k prints at 6% area coverage PL 9.17 Item 4
PL 9.15 Item 4
Waste toner bottle 100k prints at 6% area coverage PL 9.10 Item 1
DADH feed roll assembly 150k feeds PL 5.15 Item 1
1K LCSS staple cartridge 3k staples PL 26.10 Item 26
2K LCSS staple cartridge 5k staples PL 26.10 Item 11
HCSS staple cartridge 5k staples PL 26.10 Item 11
HVF staple cartridge 5k staples PL 26.10
HCSS BM staple cartridge 5k staples PL 26.10 Item 11
BM staple cartridge 2k staples PL 26.10 Item 24
Developer assembly
32-38 ppm
45-55 ppm
65-87 ppm
1000k prints
2500k prints
5000k prints PL 9.17 Item 2
PL 9.17 Item 2
PL 9.15 Item 2
Table 2 High frequency service items
Item Component Description
The
recommended
life for new
component
installation
Parts list
reference
Tray 1 feed Feed rolls All sheets fed from tray 1
after last HFSI reset 1,500k feeds PL 8.25
Tray 2 feed Feed rolls All sheets fed from tray 2
after last HFSI reset 1,500k feeds PL 8.25
Tray 3 feed Feed rolls All sheets fed from tray 3
after last HFSI reset 1,500k feeds PL 8.30 Item 2
Tray 4 feed Feed rolls All sheets fed from tray 4
after last HFSI reset 1,500k feeds PL 8.31 Item 2
Tray 1 trans Transport roll The total feeds from tray
1, 2, 3, 4 after last HFSI
reset 2,000k feeds PL 8.25 Item 8
Tray 2 trans Transport roll The total feeds from tray
2, 3, 4 after the last HFSI
reset 2,000k feeds PL 8.25 Item 8
Tray 3/4 trans Tray 3 and 4
transport roll
The total feeds from tray
3, 4 after the last HFSI
reset 2,500k feeds PL 8.30 Item 18
Bypass feeds Bypass tray
feed roll and
retard pad
assembly
The total bypass tray
feeds after the last HFSI
reset 100k feeds PL 7.30 Item 21
DADH feeds Feed roll
assembly The total DADH feeds in
all modes after the last
HFSI reset 150k feeds PL 5.15 Item 1
Inverter feeds Nip split shaft
assembly
The total turned and
duplex feeds after the last
HFSI reset 2,500k feeds PL 10.11 Item 4
Duplex sen-
sor Duplex sen-
sor actuator The total count of the
duplex sensor actuator
after the last HFSI reset 1,000k actuator
counts (32-55 ppm) PL
8.22 Item 4
Bias foam Bias contact The total sides of copies
and prints after the last
HFSI reset 500k impres-
sions PL 8.15 Item 23