Xerox Wide Format 6050 User Manual Download Page 90

Page: 90 / 304

3.2

Communication Parameter Setup
(Printer Control Panel)

This section explains the procedures for setting up the communication parameters from

the printer control panel.

Procedure

Press the <

> key with [PORT SETTING]

displayed.

Select the interface that is to be set up with the

use of the <

> and <

> keys, and then press

the <

> key.

[TCP/IP], [SERIAL], [CENTRO], and [VPI]

will be displayed, in that order.

Select the parameters with the use of the <

and <

> keys, and then press the <Set> key.

An asterisk [*] will be displayed on the right

side of the value once it has been set up.

After setting up all of the parameters, switch the

printer power off and then on for the changes to

take effect.

SNMP must be set up from Print Services on Web.

The changed parameters become valid after the machine is rebooted.

[CENTRO] and [VPI] are optional.

The changed parameters are saved to the

system when the <Set> key is pressed. It

is not necessary to save each change

individually.

Refer to the previous section for detailed

information about each of the

communication parameters.

PORT SETTING

TCP/IP

Ethernet Setting

AUTO

Summary of Contents for Wide Format 6050

















































































































































































































































































































Search results

Summary of Contents for Wide Format 6050

Reviews:

Related manuals for Wide Format 6050

Brands by name

Popular brands

Xerox Wide Format 6050, User Manual

Search results

Summary of Contents for Wide Format 6050

Reviews:

Related manuals for Wide Format 6050

Brands by name

Popular brands