Wincor Nixdorf TH210 Programmer'S Manual Download Page 98 | Manualshive

Page: 98 / 152

background image

TH210

Programmer’s Guide

94

Cancel print data in page mode

ASCII
Hexadecimal
Decimal

CAN
18
24

Deletes all the data to be printed in the “page” area. Any data from the previously selected “page”
area that is also part of the current data to be printed is deleted.

Exceptions

This command is only used in page mode.

Print data in page mode

ASCII
Hexadecimal
Decimal

ESC FF
1B 0C
27 12

Collectively prints all buffered data in the printing area.
After printing, the printer does not clear the buffered data and sets values for select print direction
in page mode (1B 54 n) and set print area in page mode (1B 57 …), and sets the position for
buffering character data.
Printer returns to standard mode through use of 0C, 1B 53, or initialization (which cancels all
settings).

Exceptions

This command is enabled only in page mode.

Select page mode

ASCII
Hexadecimal
Decimal

ESC L
1B 4C
27 76

Switches from standard mode to page mode. After printing has been completed either by the
print and return to standard mode (FF) command or select standard mode (1B 53) the printer
returns to standard mode. The developed data is deleted after being printed. For more
information see page mode in this document.
This command sets the position where data is buffered to the position specified by select print
direction in page mode (1B 54) within the printing area defined by set print area in page mode (1B
57).
This command switches the settings for the following commands (which values can be set
independently in standard mode and page mode) to those for page mode.



Set right-side character spacing (1B 20)



Select 1/6-inch line spacing (1B 32)



Set line spacing (1B 33)

It is possible only to set values for the following commands in page mode. These commands are
not executed.



Select or cancel 90 degree clockwise rotation (1B 56)

«
...
96
97
98
99
100
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: 3Doodler Pages: 8

Brand: Oki Pages: 222

Brand: Oki Pages: 4

Brand: Oki Pages: 160

Brand: quadient Pages: 130

Brand: TallyGenicom Pages: 166

Brand: FujiFilm Pages: 37

Brand: Duplo Pages: 123

Brand: Ricoh Pages: 126

Brand: Kyocera Pages: 13

Brand: Lexmark Pages: 4

Monochrome Laser

Brand: Lexmark Pages: 1

Brand: Protech Systems Pages: 140

bizhub PRO C65hc

Brand: Konica Minolta Pages: 24

Brand: Xante Pages: 106

Brand: Xante Pages: 20

Brand: NEC Pages: 90

Brand: Epson Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands