Wincor Nixdorf TH210 Programmer'S Manual Download Page 103 | Manualshive

Page: 103 / 152

background image

TH210

Programmer’s Guide

99

Macros

These commands are used to select and perform a user-defined sequence of printer operations.

Select or cancel macro definition

ASCII
Hexadecimal
Decimal

GS :
1D 3A
29 58

Starts or ends macro definition. Macro definition begins when this command is received during
normal operation and ends when this command is received during macro definition. The macro
definition is cleared, during definition of the macro when the execute macro (1D 5E) command is
received.
Normal printing occurs while the macro is defined. When the power is turned on the macro is not
defined.
The defined contents of the macro are not cleared by the initialize printer (1B 40), thus, the
initialize printer (1B 40) command may be used as part of the macro definition.
If the printer receives a second select or cancel macro definition (1D 3A) command immediately
after previously receiving a select or cancel macro definition (1D 3A) the printer remains in the
macro undefined state.

Formulas

The contents of the macro can be defined up to 2048 bytes.

Exceptions

If the macro definition exceeds 2048 bytes, excess data is not stored.

Execute macro

ASCII
Hexadecimal
Decimal

Value of

r

:

Value of

t

:

GS ^

r t m

1D 5E

r t m

29 94

r t m

The number of times to execute the macro.

The waiting time for executing the macro.

Executes a macro. After waiting for a specified period the printer waits for the paper feed button
to be pressed. After the button is pressed, the printer executes the macro once. The printer
repeats this operation the number of specified times.
When the macro is executed by pressing the paper feed button (m = 1), paper cannot be fed by
using the paper feed button.

Formulas

The waiting time is t x 100 ms for every macro execution.
m specifies macro executing mode when the LSB (least significant bit) m = 0
The macro executes r times continuously at the interval specified by t when the LSB (least
significant bit) of m = 1.

«
...
101
102
103
104
105
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: Xerox Pages: 34

ImageCLASS MF3240 Series

Brand: Canon Pages: 62

ImageCLASS MF4270

Brand: Canon Pages: 226

imageCLASS D660

Brand: Canon Pages: 8

ImageCLASS MF3240 Series

Brand: Canon Pages: 136

Color imageRUNNER C5180 Series

Brand: Canon Pages: 851

imageCLASS D320

Brand: Canon Pages: 121

imageCLASS MF212w

Brand: Canon Pages: 236

imageCLASS D760

Brand: Canon Pages: 82

imageclass LBP251dw

Brand: Canon Pages: 72

ImageCLASS MF4270

Brand: Canon Pages: 248

ImageCLASS MF4270

Brand: Canon Pages: 36

imageCLASS D760

Brand: Canon Pages: 8

imageCLASS MF4100 Series

Brand: Canon Pages: 140

imageclass LBP251dw

Brand: Canon Pages: 116

imageCLASS D860

Brand: Canon Pages: 73

imageCLASS D1320

Brand: Canon Pages: 36

ImageCLASS MF3240 Series

Brand: Canon Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands