Wincor Nixdorf TH210 Programmer'S Manual Download Page 81 | Manualshive

Page: 81 / 152

background image

TH210

Programmer’s Guide

77

If an immediate return of printer status is desired, then any of the other status commands should
be issued following this command. Once this mode is activated, the printer automatically transmits
4 status bytes whenever any of the conditions change. If an RS-232C connection with hardware
flow control is used, all four status bytes will be transmitted without checking DSR.
This command is a POS version of general printer unsolicited status functions; it uses the same
command code as older versions of the POS command, “automatic status back (ASB)” but has the
following differences:



The parameter n is an on/off switch; it does not select trigger subset



There is no immediate return when this mode is turned on



All 4 status bytes are always returned

A change in any of the following conditions will trigger the USM response:



Cash Drawer



Receipt Cover



Knife Error



Out-of-Range Printhead Temperature



Out-of-Range Voltage



Paper Exhaust Status

Related information

When Unsolicited Status Mode is enabled using this command, the status transmitted by other
commands and the USM status are differentiated according to the information found in
Recognizing Data from the printer, which follows the USM return description.
The status bytes to be transmitted are described in the following four tables.
Byte 1 = printer information
Byte 2 = error information
Byte 3 = paper sensor information
Byte 4 = paper sensor information

First byte (Printer Information)

Bit

Off/On Hex

Decimal

Status for USM

0

Off

00

0

Not used. Fixed to off.

1

Off

00

0

Not used. Fixed to off.

2

Off

00

0

One or both cash drawers open.

On

04

4

Both cash drawers closed.

3

Off

00

0

Not busy at the RS232C interface.

On

08

8

Printer is busy at the RS232C interface.

4

On

10

16

Not used. Fixed to on.

5

Off

00

0

Receipt cover closed.

On

20

32

Receipt cover open.

6

Off

00

0

Paper feed button is not pressed.

On

40

64

Paper feed button is pressed.

7

Off

00

0

Not used. Fixed to off.

«
...
79
80
81
82
83
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: m3d Pages: 23

Brand: m3d Pages: 26

Brand: Oki Pages: 2

Brand: CAB Pages: 40

Brand: Qilive Pages: 398

Brand: Canon Pages: 12

Brand: MEFA Pages: 2

Brand: Triumph Adler Pages: 4

Brand: Intuitive Pages: 18

WorkCentre WC7545

Brand: Xerox Pages: 8

Brand: AstroJet Pages: 32

Brand: Kyocera Pages: 28

Brand: Xerox Pages: 2

CHAMPION MSP 450

Brand: TVS electronics Pages: 92

imagePROGRAF TM-355

Brand: Canon Pages: 52

Brand: Wang Pages: 39

Brand: Oce Pages: 196

Brand: 3D Systems Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands