Wincor Nixdorf TH210 Programmer'S Manual Download Page 46 | Manualshive

Page: 46 / 152

background image

TH210

Programmer’s Guide

42

Related information

In standard mode, when double-height mode is selected, the character is enlarged in the paper
feed direction, and when double-width mode is selected it is enlarged perpendicular to the paper
feed direction. In 90° clockwise-rotated mode, the relationship between double-height and
double-width is reversed. In page mode, double-height and double-width are on the character
orientation.
Look in chapter “Programming the Printer, Character appearance” for a description of standard
and compressed character pitches.
The bits in this command perform the same function as the stand-alone functions:

1B 16

n

Select pitch

1B 45

n

Emphasized

1B 47

n

Double-strike

12

Double-wide

13

Single-wide

1B 2D

n

Underline

Select or cancel user-defined character set

ASCII

ESC

% n

Hexadecimal

1B 25

n

Decimal

27 37

n

Value of

n

:

0 = Code Page 437
1 = User Defined (RAM)
2 = Code Page 850

Range of

n

:

0–2

Default:

0 (Code Page 437)

Selects the character set until the printer is initialized, reset, or powered off. When an undefined
RAM character is selected, the current active ROM code page character is used. Look in Chapter
“Programming the Printer, Character appearance” for the character sets.

Exception:

The character sets cannot be used together on the same line.

Related information

In LEGACY emulation, the low order bit of n is used to select the user-defined character set and the
current active ROM code page is not affected.

Define user-defined character set

ASCII

ESC &

s c1 c2

[character 1 data] ... [character k data]

Hexadecimal

1B 26

s c1 c2

[character 1 data] ... [character k data]

Decimal

27 38

s c1 c2

[character 1 data] ... [character k data]

Values and ranges:

s

= 3, the number of bytes (vertically) in the character cell

c

= the ASCII codes of the first (c1) and last (c2) characters respectively

«
...
44
45
46
47
48
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: Xyron Pages: 6

Brand: Xerox Pages: 2

Brand: Xerox Pages: 40

Brand: Xerox Pages: 69

Brand: Xerox Pages: 42

Brand: G3D Pages: 4

Brand: TallyGenicom Pages: 310

Brand: TallyGenicom Pages: 330

Brand: Oki Pages: 222

Brand: Oki Pages: 4

Brand: Oki Pages: 160

DC240 - DocuColor 240 Color Laser

Brand: Xerox Pages: 2

ColourLaser series guide

Brand: Xante Pages: 31

Brand: Xante Pages: 31

Accel-a-Writer 812

Brand: Xante Pages: 12

Brand: Oki Pages: 104

Brand: Tally Pages: 28

Brand: Kyocera Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands