Wincor Nixdorf TH210 Programmer'S Manual Download Page 105 | Manualshive

Page: 105 / 152

background image

TH210

Programmer’s Guide

101

n = 49 (ASCII n = 1) HEX 31

Loads active logo to flash memory. This is the default condition for logo flash storage. A logo
defined following this command is stored in flash memory.

n = 50 (ASCII n = 2) HEX 32

Loads user-defined characters to RAM only. This is the default condition for user-defined character
storage. Any user- defined characters defined following this command are not preserved over a
power cycle.

n = 51 (ASCII n = 3) HEX 33

Loads user-defined characters to flash memory. An application must use this command to store
user-defined characters in flash memory. Any user-defined characters defined following this
command are stored in flash memory. A user-defined character cannot be redefined in flash
memory. The flash memory page must be erased by an application before redefining user-defined
characters. For more information, see the erase user flash sector (1D 40 n) command.
Specifies whether to load the logos or user-defined characters to logo/font flash memory or to
RAM (volatile memory). The selection remains in effect until it is changed via this command or
until the power cycles. To specify permanent font flash, also send 1D 22 81 01.

Related information

This command is recognized in Native mode. In A793 and LEGACY emulations, parameter bytes go
into the print buffer.

Flash memory user sectors allocation

ASCII
Hexadecimal
Decimal

Value of

n1

:

Value of

n2

:

GS” U

n1

n

1D 22 55

n1 n2

29 34 85

n1 n2

1 (see below)

1 (see below)

n

1 is the number of 64k sectors used for logos and user-defined characters.

n

2 is the number of 64k sectors used for user data storage.

n1 + n2 <= 6 (dec) (1M)

n1 + n2

<= 22 (dec) 16 (hex) (2M)

If

n

1 +

n

2 is greater than the maximum number of sectors available, the command is ignored. The

printer returns NACK. Issuing this command with parameters different from current parameters
will erase all sectors. The printer returns ACK. Issuing this command with parameters the same as
current parameters will do nothing. The printer returns ACK.
Note: Flash memory is made up of user and program code. Therefore, the available flash memory
space will vary with the amount of program code utilized.

Flash object area pack

ASCII
Hexadecimal
Decimal

Value of

n1

:

GS” `

n1

1D 22 60

n1

29 34 96

n1

n

1 specifies

«
...
103
104
105
106
107
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: IBM Pages: 102

Brand: Xerox Pages: 3

Brand: Xerox Pages: 2

WorkCentre 3615

Brand: Xerox Pages: 20

Brand: Citizen Pages: 133

5550B - Phaser B/W Laser Printer

Brand: Xerox Pages: 117

WorkCentre 3345

Brand: Xerox Pages: 18

Brand: Maxim Pages: 69

Brand: ImageTech Pages: 44

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: Citizen Pages: 3

Brand: Microcom Pages: 73

Brand: Tascam Pages: 2

Brand: GearRev Pages: 41

apeosport 550 I

Brand: Xerox Pages: 160

ApeosPort-IV C5580

Brand: Fuji Xerox Pages: 739

Brand: Ricoh Pages: 678

Brand: ZKTeco Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands