Wincor Nixdorf TH210 Programmer'S Manual Download Page 48 | Manualshive

Page: 48 / 152

background image

TH210

Programmer’s Guide

44

Defines and enters downloaded characters into RAM. The command may be used to overwrite
single characters. User- defined characters are available until power is turned off or the Initialize
Printer command (1B 40) is received.
Any invalid byte (

s, c1, c2, n1

) aborts the command.

Related information
User-defined characters can be set for each pitch independently by selecting the pitch using the 1B
21 command.
See 1D 22

n

(select memory type) to save user-defined characters

Select or cancel underline mode

ASCII

ESC

- n

Hexadecimal

1B 2D

n

Decimal

27 45

n

Value of

n

:

Decimal

Hex

0, 48

30 = Cancel underline mode

1, 49

31 = Select underline mode

2, 50

32 = Select double thickness

underline mode

Default:

0 (Cancel underline mode)

Turns underline mode on or off until the printer is initialized, reset, or powered off. Underlines
cannot be printed for spaces set by the horizontal tab, set absolute start position, or set relative
print position commands. Underline thickness grows as the vertical size of the character grows.
This command and the Select Print Mode(s) command (1B 21) turn underline on and off in the
same way.

Exceptions

This command is ignored if n is out of the specified range.
This command does not affect HRI characters.

Related information

In A793 emulation, this command is unrecognized and the parameter

n

is put into the print buffer.

Copy character set from ROM to RAM

ASCII

ESC: 00

Hexadecimal

1B 3A 30 30 30

Decimal

27 58 0 0 0

Default:

Current active ROM code page

Copies characters in the active ROM set to RAM. Use this command to re-initialize the user-defined
character set. Code page 437 is copied by default at initialization.
This command is ignored if current font is the user font.

Related information

To modify characters in one of the character set variations, such as rotated print, select one of the
rotated print commands, copy to RAM, then use the define user-defined character set command
(1B 26).

«
...
46
47
48
49
50
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

imagePROGRAF W8400

Brand: Canon Pages: 24

Super G3 FAX Board-T1

Brand: Canon Pages: 16

imagePROGRAF TZ-30000

Brand: Canon Pages: 66

imagePROGRAF W7200

Brand: Canon Pages: 126

imagePROGRAFi iPF840 series

Brand: Canon Pages: 149

Brand: Canon Pages: 166

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 2

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Olympus Pages: 3

BW Remote Operators Software Kit-A1

Brand: Canon Pages: 20

imageRUNNER 2420

Brand: Canon Pages: 30

Brand: Canon Pages: 51

imageCLASS LBP325dn

Brand: Canon Pages: 252

Brand: QMS Pages: 86

Brand: Javelin Pages: 2

Brand: TallyGenicom Pages: 145

T2265 SprintPro

Brand: Tally Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands