Wincor Nixdorf TH210 Programmer'S Manual Download Page 49 | Manualshive

Page: 49 / 152

background image

TH210

Programmer’s Guide

45

Cancel user-defined character

ASCII

ESC?

n

Hexadecimal

1B 3F

n

Decimal

27 63

n

Value of

n

:

Specified character code.

Range of

n

:

32-255

Cancels the pattern defined for the character code specified by n. After the user-defined character
is canceled, the corresponding pattern from current active ROM code page is printed.
User-defined characters can be cancelled for each pitch independently by selecting the pitch using
the 1B 21 command.

Exceptions

This command is ignored if n is out of range or if the user-defined character is not defined.

Select or cancel emphasized mode

ASCII

ESC E

n

Hexadecimal

1B 45

n

Decimal

27 69

n

Value of

n

:

0 (bit 0) not selected
1 (bit 0) selected
(When 0 and 1 are the least significant bit, LSB)

Range of

n

:

0-255

Default:

0 (off)

Starts or stops emphasized printing until the printer is initialized, reset, or powered off. The printer
is reset to the standard print mode after a clear printer (0x10) command is received.

Exceptions

Only the lowest bit of n is effective. Emphasized printing cannot be used with bit-images or
downloaded bit-images.
This command does not affect HRI characters.

Related information

This command and the select print mode(s) command (1B 21) function identically. They should
have the same setting when used together.
In A793 emulation, this command is unrecognized and the parameter byte is put into the print
buffer.

«
...
47
48
49
50
51
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

All in One Printer

Brand: Xerox Pages: 3

Brand: Felix printers Pages: 9

Brand: Felix printers Pages: 15

Brand: Felix printers Pages: 15

Brand: Olivetti Pages: 2

Brand: Olivetti Pages: 109

Brand: Olivetti Pages: 111

Brand: Olivetti Pages: 8

Brand: Xerox Pages: 9

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 4

Brand: Xerox Pages: 150

Brand: Xerox Pages: 4

Brand: Xerox Pages: 6

Brand: Xerox Pages: 2

DocuPrint N2125

Brand: Xerox Pages: 246

DocuPrint N2025

Brand: Xerox Pages: 378

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands