Wincor Nixdorf TH210 Programmer'S Manual Download Page 96 | Manualshive

Page: 96 / 152

background image

TH210

Programmer’s Guide

92

This command stores the DataMatrix symbol data (d1...dk) in the symbol storage area. k bytes of
d1...dk are processed as the symbol data
Notes
The symbol data saved in the symbol storage area by this command is encoded by printing and
transmission of this command. After printing and transmission are executed, the symbol data in
the symbol storage area is kept. FNC1 character must be specified as ESC (Hex = 1BH / Decimal =
27) + “1” (Hex = 31H / Decimal = 49). ESC itself must be specified as ESC + ESC.
The symbol data saved in the symbol storage area by this command is kept until the following
processing is performed:
This function is executed
1b 40 is executed
The printer is reset or the power is turned off.

Print DataMatrix symbol data in the symbol storage area

ASCII
Hexadecimal
Decimal

GS ( k pL pH cn fn m
1D 28 6B 03 00 36 54 30
29 40 107 0 54 84 48

Values and Ranges:

Value:

Ranges:

(pL + pH x 256)

3

cn

54

fn

81

m

48

This command encodes and prints the DataMatrix symbol data stored in the symbol storage area.
Notes
Use this command when the printer is at the beginning of a line, or there is no data in the print
buffer.
If the symbol size exceeds the print area, the printer feeds the paper as much as the symbol’s
height, without printing the symbol.
The quiet zone (the space at the top, bottom, right, and left of the symbols, which is specified by
the DataMatrix standard) is not included in the printing data. Be sure to include the quiet zone
when using this function.
If there are any of the errors described below in the data of the symbol storage area, the barcode
will not be printed.



There is no data.



When there is a problem with the amount of data saved in the symbol storage area.



When the data saved in the symbol storage area includes data outside the domain.

Printing of symbol is not affected by print mode (emphasized, double-strike, underline, or font
size), except for upside-down print mode.
The following functions are not supported:
Structured Append Symbols Macro Character
Reader Programming Character
ECI: Extended Channel Interpretation

«
...
94
95
96
97
98
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: Oki Pages: 2

Brand: Datecs Pages: 29

Brand: TallyGenicom Pages: 92

Brand: Lexmark Pages: 500

BIO X Autocalibration Kit

Brand: Cellink Pages: 17

Brand: Savin Pages: 6

Aficio SP C240SF

Brand: Ricoh Pages: 14

FELIX Pro 3 Touch

Brand: Felix printers Pages: 29

Brand: Oki Pages: 187

KYOCERA FS-C8100DN

Brand: Kyocera Pages: 12

Brand: GearRev Pages: 41

Brand: Ultimaker Pages: 34

Brand: Copystar Pages: 1

Brand: Epson Pages: 277

Brand: Epson Pages: 288

Brand: Epson Pages: 283

Brand: Epson Pages: 60

Brand: WOOSIM Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands