Wincor Nixdorf TH210 Programmer'S Manual Download Page 65 | Manualshive

Page: 65 / 152

background image

TH210

Programmer’s Guide

61

Print downloaded bit image

ASCII

GS /

m

Hexadecimal

1d 2F

m

Decimal

29 47

m

Value and range of

m

:

This command is used to print a previously stored monochrome (defined by 1D 2A) from printer
memory on the receipt station. The logo is identified as the one indicated by the most recent
select current logo command or 0 if a select current logo command has not yet been given.
Parameter m is interpreted as follows:

Value of

m

Print mode

Vertical DPI

Horizontal DPI

0, 30

Normal

203

203

1, 31

Double wide

203

101

2, 32

Double high

101

203

3, 33

Double wide/ Double high

101

101

The indexed downloaded bit image from RAM or flash will be printed on the receipt station at a
size specified by

m

. If the bit image is a monochrome one, it is printed in the current color;

otherwise it is printed as a two-color image. If doubling or quadrupling exceeds the print paper
width maximums (576 with 80mm paper) the left side of the image is printed and the bits to the
right of the maximum column are discarded. If the available width is greater than the bit image, its
printing will adhere to any currently set right, left, or center justification. This command is ignored
if the index refers to an undefined logo/ bit image.

«
...
63
64
65
66
67
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: Hanin Pages: 27

Brand: Canon Pages: 65

IMAGE M4100 Series

Brand: G&G Pages: 147

Brand: Velleman Pages: 44

Imagistics 2500

Brand: Axis Pages: 16

Brand: Rapid Shape Pages: 44

Brand: Linux Pages: 8

Brand: Jolimark Pages: 65

Brand: WANHAO Pages: 18

Brand: LevelOne Pages: 88

Brand: VASTEX Pages: 8

Brand: Brady Pages: 48

Brand: Oce Pages: 76

Brand: Xerox Pages: 4

Brand: Kyocera Pages: 410

Brand: Canon Pages: 436

Pixma TS8700 Series

Brand: Canon Pages: 589

Brand: Canon Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands