Wincor Nixdorf TH210 Programmer'S Manual Download Page 14 | Manualshive

Page: 14 / 152

background image

TH210

Programmer’s Guide

10

3.

Push the paper feed button. The receipt station prints all code pages and cuts the
receipt.

4.

To repeat this test, push the paper feed button again.

To exit the receipt test mode:

1.

Enter the configuration menu again.

2.

Disable the receipt test mode.

3.

Exit the configuration menu.

The printer is on-line and can again communicate normally with the host computer.

Electronic Journal Datascope Diagnostic

1F 03 18 02 n=1, turn on electronic journal datascope, run time only
1F 03 18 02 n=0, n>1, turn off electronic journal datascope, run time only
1F 03 18 03 n=1, turn on electronic journal datascope, configuration saved over power cycle
1F 03 18 03 n=0, n>1, turn off electronic journal datascope, configuration saved over power cycle
When enabled, “Auto Journal : Datascope” prints on the second diagnostic page.
This diagnostic is for debugging purposes, and should be used only under the direction of customer
support.

Printer emulations

To change the printer emulations settings, enter the configuration menu, select
“Emulation/Software Options” from the main menu and answer “Yes” to “Set printer mode?”
printed on the receipt. This will take you to the instructions for setting the printer emulation.
Caution: Be extremely careful changing any of the printer settings to avoid inadvertently changing
other settings that might affect the performance of the printer.
Press the paper feed button as instructed to select the printer emulation you want.



Native mode



A794 emulation



A793 emulation



LEGACY emulation

Note: Press the paper feed button for at least one second to validate the selection.

Setting the printer emulation

Refer to the section “Configuring the printer”.

Printer settings and functions

To change the printer settings and functions, enter the configuration menu, select the sub-menu
from the main menu and answer the questions printed on the receipt until you come to the
instructions for selecting the printer settings.
Caution: Be extremely careful changing any of the printer settings to avoid inadvertently changing
other settings that might affect the performance of the printer.
Press the paper feed button as instructed to select the printer settings you want.

«
...
12
13
14
15
16
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: Magicard Pages: 6

Brand: MEFA Pages: 2

Brand: Riso Pages: 208

Brand: Xerox Pages: 150

WorkCentre 6655i

Brand: Xerox Pages: 282

Brand: Unisys Pages: 144

Brand: Star Micronics Pages: 127

Brand: Daewoo Pages: 37

Brand: Ocom Pages: 23

Brand: Z Corporation Pages: 70

Brand: Canon Pages: 70

Brand: AccuBANKER Pages: 5

Brand: Savin Pages: 90

Brand: SATO Pages: 241

Brand: Brother Pages: 116

AcuLaser CX11 Series

Brand: Epson Pages: 668

301P - DP Print Server

Brand: D-Link Pages: 150

Brand: Duplo Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands