Wincor Nixdorf TH210 Programmer'S Manual Download Page 13 | Manualshive

Page: 13 / 152

background image

TH210

Programmer’s Guide

9

Enable or disable data scope mode

The data scope mode test prints a hexadecimal dump of all data sent to the printer: “1” prints as
hexadecimal 31, “A” as hexadecimal 41 and so on. This helps troubleshoot communication
problems and runs during a normal application (after being enabled through printer configuration).
Note: Data scope mode is usually considered a level 1 diagnostic test.
Data scope mode is enabled and disabled by selecting the “Diagnostics Modes” sub-menu of the
configuration menu. Press the paper feed button as instructed on the “Diagnostics Modes Menu”
to enable or disable the data scope mode test.



Off, normal mode (Data scope mode disabled)



Data scope mode with or without graphics (enabled)

Note: Press the paper feed button for at least one second to validate the selection.

To run the data scope mode:

1.

After you have enabled the data scope mode, exit the configuration menu.

2.

Run a transaction from the host computer.

All commands and data sent from the host computer will be printed as hexadecimal characters as
shown in the illustration.

To exit the data scope mode:

1.

Enter the configuration menu again.

2.

Disable the data scope mode.

3.

Exit the configuration menu.

The printer is on-line and can communicate normally with the host computer.

Enabling the data scope mode

Refer to the section “Configuring the printer”.

Enable or disable receipt test mode

The receipt test mode verifies proper receipt printing. Receipt test is enabled and disabled by
selecting the “Diagnostics Modes” sub-menu of the configuration menu. See “Configuring the
printer”, for instructions on how to enter the configuration menu.

To run the receipt test mode:

1.

Enable the receipt test mode in the configuration menu.

2.

Exit the configuration menu.

«
...
11
12
13
14
15
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: QMS Pages: 86

Jetprinter Disney Edition Z615 Series

Brand: Lexmark Pages: 2

Brand: QMS Pages: 311

Brand: Zmorph Pages: 16

Brand: Canon Pages: 21

imageRUNNER ADVANCE 4251

Brand: Canon Pages: 12

Brand: Sagem Pages: 126

WorkCentre XD Series

Brand: Xerox Pages: 63

Brand: Sagem Pages: 102

Brand: Minolta Pages: 227

Brand: U-Line Pages: 30

DocumentCentre C240 Series

Brand: Fuji Xerox Pages: 275

Brand: Creality 3D Pages: 65

ID MAKER Zenius

Brand: IDVille Pages: 66

Brand: Aficio Pages: 92

Brand: IOGear Pages: 48

6250N - Phaser Color Laser Printer

Brand: Xerox Pages: 467

MAC TECHNICAL REFERANCE C7350

Brand: Oki Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands