Wincor Nixdorf TH210 Programmer'S Manual Download Page 34

Page: 34 / 152

TH210

Programmer’s Guide

Feed

print lines

ASCII

DC4

Hexadecimal

Decimal

Value of

The number of lines to feed at current line
height setting.

Range of

0–255 in Native mode
0–127 in A793 emulation

Feeds the paper n lines at the current line height without printing. Ignored on receipt if current line
is not empty.
Related information
This is ignored in LEGACY emulation and the parameter byte goes into the print buffer.

Feed n dot rows

ASCII

NAK

Hexadecimal

Decimal

Value of

/203 inch

Range of

0–255 in Native mode
0–127 in A793 emulation

Feeds the paper

dot rows (

/8 mm,

/203 inch), without printing. Receipt moves

rows if the

print buffer is empty.

Related information

This is ignored in LEGACY emulation and the parameter byte goes into the print buffer.

Add

extra dot rows

ASCII

SYN

Hexadecimal

Decimal

Value of

Number of extra dot rows

Range of

0–16

Default:

3 extra dot rows

Adds

extra dot rows (

/8 mm

, n

/203 inch) to the character height to increase space between

print lines or decrease the number of lines per inch.

Formulas

The following table shows the relationship between the number of lines per inch and each extra
dot row added:

Summary of Contents for TH210

























































































































































Search results

Summary of Contents for TH210

Reviews:

Related manuals for TH210

Brands by name

Popular brands

Wincor Nixdorf TH210, Programmer'S Manual

Search results

Summary of Contents for TH210

Reviews:

Related manuals for TH210

Brands by name

Popular brands