Wincor Nixdorf TH210 Programmer'S Manual Download Page 15 | Manualshive

Page: 15 / 152

background image

TH210

Programmer’s Guide

11

Select the emulation/software options sub-menu to set:



Printer Mode

This function is used to set the printer emulation to Native, A794, A793 or Legacy emulation.



Printer ID mode

This function is used to determine what printer ID value is returned in response to a Transmit
printer ID command (1D 49 n) when the printer is in A794 emulation mode. The printer can be
configured to send back the ID of the TH210, A794, A793 or Application Compatible Escape
Command systems.



Default lines per inch

This function allows you to set the default for lines per inch to:



8.13 lines per inch



7.52 lines per inch



6.77 lines per inch



6.00 lines per inch



Carriage return usage

This function allows the printer to ignore or use the carriage return (hexadecimal 0D) command
depending on the application. Some applications expect the command to be ignored while others
use the command as a print command.



Code 128 Check Digit

Enables or disables the calculation of the check digit.



Default font

Sets the default for monochrome, two-color, and LEGACY emulations.



Font size

Allows user to set font size for the emulation being used.



Journal Print

Enables or disables operator action.

Select the hardware options sub-menu to set:



Print density (monochrome papers only)

Adjusts printhead energy level to darken printout or adjust for paper variations. When printer
prints high-density print lines (text or graphics), it automatically slows down. Factory setting for
the TH210 is 100%.
WARNING: Choose a print density setting no higher than necessary to achieve acceptable print
density. Failure to observe this rule may result in a printer service call and may void the printer
warranty. Running at a higher energy level will reduce the printhead life. Consult your Wincor
Nixdorf technical support specialist if you have questions.



Power supply level (Max power)

You can choose from these power settings to match the power supply:

Auto (for Wincor Nixdorf power supplies)

«
...
13
14
15
16
17
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: QMS Pages: 160

Brand: QMS Pages: 110

Brand: QMS Pages: 158

Brand: CAB Pages: 144

Brand: QMS Pages: 311

Brand: Xerox Pages: 414

Brand: Oki Pages: 48

Brand: Oki Pages: 20

Brand: Oki Pages: 42

Brand: Oki Pages: 2

Brand: Oki Pages: 8

Brand: Oki Pages: 13

Brand: Oce Pages: 2

Brand: Oki Pages: 193

Brand: Xerox Pages: 16

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 6

Brand: Xerox Pages: 2

Brand: Xerox Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands