manualshive.com logo in svg

Volvo EC60E, Operator'S Manual, Page: 83 / 342

Share
Download
Volvo EC60E Operator'S Manual Download Page 83

2 One-time code (optional equipment) : This is

used for setting a one-time code when the

machine is immobilized with level 3 remote

immobilization or no coverage warning

condition.

The machine owner gets the one-time code from

the dealer. The dealer gets an 8-digit random

code in the CareTrack portal with 8-digit seed

(number shown on I-ECU) and machine serial

number.

Alarm texts for anti-theft system

Information

- The blue information symbol is shown.

- The buzzer sounds two times.

- Alarm text is shown for seven seconds and then

changes to operating display.

V1137933

Geofence broken

GO BACK TO SITE

V1137935

Timefence broken

Go back to site

Geofence broken

Timefence broken

V1160932

7 4 0 9 7 1 2

Current 8-digit seed:

0

Enter one-time code:

Pin-code menu

One-time code

Pin-code menu

Owner menu

 

 

82

Instrument panels

Display unit

Summary of Contents for EC60E























































































































































































































































































































































Reviews:

No comments