Volvo EC60E Operator'S Manual Download Page 290

Page: 290 / 342

For Volvo tooth system (VTS)

Replace the bucket teeth before the adaptors wear

away.

WARNING

Risk of splinter injury.

Striking the bucket pin with a hammer could cause

metal chips to fly around and cause serious splinter

injury.

Always wear face and eye protection, hard hat and

gloves while removing and installing the bucket

pins.
A special tool may be ordered to facilitate

replacement of teeth. The tool are available in

different sizes depending on tooth size. Contact

your dealer for further information.

Removing tooth

1 Lower the bucket horizontally on a block and

angle it slightly upward.

2 Move the control lockout lever up to lock the

system securely and stop the engine.

3 Clean the opening for tooth adapter locking

device.

4 Knock out the locking device with a hammer and

the tool or other suitable drift.

5 Remove tooth.

V1066078

Special tool

V1066079

Knock out the locking device

Maintenance

Maintenance service, when required

289

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 290 / 342

Search results

Summary of Contents for EC60E

Reviews: